Reinforced straighten cutter device has three main components: straightening, traction, and Cutting. Specifically, (1) Straightening parts: the main tune of five straight inside straight mold components. Reinforced put disk, not in a straight through in tune straightening die on the line, and was forced to pull the roller forward drag, this time, the motor drives the tone straight to 2800 rpm rotational speed, straight mold making steel by straightening bent in all directions, so that the bars get straight and rust, the surface scale removed. (2) traction: driven by the motor while the other pulley, gear change of direction by a pair of bevel gears, bevel gear and drive at the same speed reverse rotation of a pair of gear through a reduction gear, rotating the upper and lower pressure rollers, steel is pressed roll up and down within a groove, efficient steel cutting machine, circular motion roller traction bars straight to move forward. (3) and Cutting parts: the length board, length rod and bladed knife sets consisting of sliding, a cutting device is said to rotate with the crank up and down movement of the hammer. Length front plate with a spring, sliding the rear side of the knife station is located hammer, steel cutting machine technology, reinforcing bars until a predetermined length, length plate to the front of the top compression spring, by sliding rod length knife sets to move forward, in under the hammer blow on the hammer blow down movement of the movable blade, make steel cutting. At this time, the compressed spring length board bounce back into place, slide knife sets also will be reset. Reinforced straighten cutter can be achieved through electronic components NC, since the power cut-off material powder is relatively high, 1-2 mm deviation controlled cases. Gongyi City, Di Metallurgical Equipment Co., Ltd. as a company specializing in the development and production of cold-rolled unit sales of the manufacturers, production of steel processing machinery and equipment are: cold rolling mill, bending hoop machine, cold rolling equipment, costal cold rolling mill, cold-rolled ribbed steel equipment, cold-rolled ribbed steel bar production line, hot-rolled-up machine, bar straightening cutting machine, bar straightening machines, steel cutting machine, flying cut-off machines, steel stretching machine, high frequency quenching equipment, three steel Straightening and Cutting Machine, word round to line machine, steel flip rack and so on. Generally, cold-rolled ribbed steel bars are small in diameter, it is the common wire of the cold extrusion. After plastic deformation, the strength is drastically increased, while the plasticity is drastically reduced, thus giving rise to the kind of situation you say. Carbon 2% (by mass) or less steel, more than 2 percent of iron. Iron wrought iron than the carbon content is high, steel cutting machine latest offer, the higher the carbon content, the greater the hardness, toughness worse. Pure Iron is the substance does not contain any impurities idealized. Iron generally refers to the carbon content of 2 to 4.3 percent of the iron alloy. Also known as cast iron. Pig iron in addition to carbon, also contain silicon, manganese, and a small amount of sulfur, phosphorus, etc., it can not be wrought cast. According to the different forms of pig iron in the presence of carbon, can be divided into steel-making pig iron, cast iron and ductile iron and so are several. Steelmaking pig iron in the form of iron carbide carbon mainly exists, its cross section is white, generally known as white iron. This performance is hard and brittle pig iron, are generally used as raw material for steel making. Foundry iron in carbon flake graphite morphology to exist, it's fracture is gray, usually known as gray iron. Because graphite is soft, it has a lubricating effect, which cast iron has good cutting, wear and casting properties. But it's not enough anti-bit strength, steel cutting machine, it can not be wrought only be used in the manufacture of various items, such as casting a variety of machine bed seat, iron tubes. Ductile iron with spherical graphite carbon in the form of existence, and is close to steel and its mechanical properties far better than gray iron, it has excellent casting, machining and wear, have a certain flexibility, widely used in the manufacture of the crankshaft, gears, pistons and other senior casting and a variety of mechanical parts. In addition to silicon, manganese, nickel or other elements particularly high amount of iron, called iron alloy, such as ferrosilicon, ferromanganese, etc., often used for steelmaking raw materials. Adding some alloys in steel making pig iron, can improve the properties of steel. Steel cutting machine _ _ Kindi metallurgy efficient steel cutting machine provided by Di Metallurgical Equipment Co. Steel cutting machine _ _ Kindi metallurgy efficient steel cutting machine is Di Metallurgical Equipment Co., Ltd. (www.ye-jin.com) this year introduced a new upgrade, the above picture is for reference only, please call the contact or pictures on this page phone, for the latest information, contact: Liu.