Jinshan licensing procedures a steel cutter. Pick-material countertops should be level and lower cutter, table length can be determined according to the length of the processed material. 2. Before you start, you should check to make sure no cracks cutter, knife bolt, solid shield. Then rotate the pulley by hand to check the gear meshing clearance, adjust the cutter clearance. 3. After starting, you should first dry run, check after each transmission parts and bearings in normal operation, before the operation. 4. When the machinery does not meet the normal speed, not cut material. When cutting, use the cutter, the lower parts, quickly put clenched steel blade alignment, the operator should stand on the side of force to suppress the fixed blade steel, should be reinforced to prevent the end of the pop-up hurt. Do both sides of the blade with both hands holding the steel sub-leaning feeding. 5. Shall not exceed the shear strength of the diameter and the red-hot steel and reinforced mechanical nameplate. When a plurality of cutting steel, the total cross-sectional area should be within the specified range. 6. When cut low-alloy steel, replace the high hardness cutter, cutting diameter should be consistent with mechanical nameplate. 7. When cutting short material, distance between the hand and the knife should be maintained at 150mm or more, such as when hand side is less than 400mm, should be used to clamp the steel casing or suppress short head or folder in prison. 8. Operation, prohibited by hand directly decapitation and remove debris near the cutter. Rebar cutter swing around and around, not stay non-operators. 9. When they find the mechanical operation is not normal, abnormal noise or skew cutter, you should immediately downtime. 10. After the operation, it should cut off the power, steel brush to remove debris between the cutter, make the machine clean lubrication. 11. Hydraulic front cutting machine operation, check that the hydraulic oil level and motor rotation direction to meet the requirements. After the start, it should load operation, loose open valve, drain the body of the air cylinder net, only 12 were cut tendons. Manual before using hydraulic cutting machine, oil drain valve should be tightened in a clockwise direction, after cutting is completed, immediately unscrew counterclockwise. Job steel cutting machine worth, steady hand should be cut off the machine, and wear insulated gloves. Steel cutting machine know the correct method of operation, not only to promote the normal use of equipment ribbed steel cutting machine, improve production efficiency steel cutting machine, you can also save more time and reduce the strength of the labor force. (1) The selection of materials should be kept at a low level countertop fine steel cutting machines, workstations based on the actual length of the required length of processing materials to be able to be determined. (2) before the device is started, you should first be carefully checked to ensure that no cracks in steel cutter, knife bolt plus a solid set, but also to replace the cover. Then to open the handwheel Oh, and to double-check the clearance gear to adjust the cutter. (3) steel cutting machines running start, you should first of its empty running at each transmission parts and bearings rotate to keep working condition, in order to work properly. If (4) steel cutting machine did not reach normal operating speed, then the firm can not cut materials. When cutting, to use the cutter, the operator must stand hard pressed steel fixed position and the side of the blade should be reinforced, so in order to prevent the pop wounding steel ends. At the same time also prohibited on both sides with both hands holding the steel bent to transport materials. (5) must not exceed the diameter of the shear strength of steel and reinforced mechanical nameplate. When a plurality of steel cut together, the total cross-sectional area must be controlled among a reasonable range. (6) When the lower aluminum cutting, working at high hardness should be replacing the knife, in accordance with the cut diameter should be performed mechanically nameplate. (7) the distance between the cutter and cut the material should be maintained at higher than one hundred and fifty millimeters of standards, such as the distance by holding batsu is within four hundred millimeters, the need to strengthen or distance sleeve and fixture The short head pressed firmly reinforced. (8) operation, the ban on bare hands to clear the debris, especially near decapitation knives and groceries. Steel cutting opportunity swing around and around in this process should remain the operator side. (9) If steel cutting machine is not working properly, or abnormal sound and display skew cutter, you should immediately stop the operation of the machine, but also timely maintenance. (10) Upon completion of the machine is running, you should cut off the power supply, you should use a wire brush to the debris between the machine and the cutter to clear, clean and lubricate the machine. Gansu JD steel cutting machine | Kindi metallurgy (certified) | steel cutting machine provided by Kindi Metallurgical Equipment Limited. Kindi Metallurgical Equipment Co., Ltd. (www.ye-jin.com) is Zhengzhou, reinforced and prestressed machinery leaders, over the years, the company is implementing the scientific management, innovation and development, the principle of honesty and trustworthiness, and satisfy customer needs . In Kindi metallurgy leadership with the staff warmly welcome all inquiries negotiations to create Kindi metallurgical a better future.